rohitkpatil
05-30-2008, 10:55 PM
Hi,
I am using Leo4all V3 10.5.2 with Vista dual boot (Ntldr, Chain 0, boot.ini, tboot at root of c)
I used shrink option from Vista to create 10 GB space for installation of OSx86.
After that i decided to make one more drive for installation of more Mac softwares (Office, photoshop etc)
So i took out some more space from other Vista drive ..around 15 GB.
I booted to Mac, and using disk utility i formatted that space with Mac OS x journeled.
But after reboot it asked me to "INSERT DISK , BOOT FAILURE".
I repaired with Vista Installation dics in just 2 mins. and booted to Vista. I saw in Disk Manager that This newly created 15 GB partition is set to (Active, Primary partition) , The old 10 GB where my OSx86 is installed is (Primary partition).
I just rebooted my system, and now i can go into OS x. OS x shows all partition properly, including the new 15 GB.
But in Vista it is showing the main OS X installation drive as (Primary), the second OS X 15 GB drive is shown as (Active , Primary) and Vista is (Active, Primary, ......sum more txt )
I have no problem in booting, i can boot selecting OS, but this secondary OS X Partition is shown as Active in Vista. So i am concerned. Is is appropriate ?
Also Inside OS , patching of Marvins utility not taking place. I put patcher , cpuid.txt files in ROOT folder, then run command as
mount -uw /
./patcher ./cpuid.txt
But now they are not getting patched. Saying 0 files patched.
Please help, can any1 tell me if is it because of that Active second OS x partition ??
How to go about Marvin's AMD utility..please help
System config:
AMD Athlon FX60
Asus A8N SLI Deluxe 1805 bios
2 GB Mushkin DDR500 @ 400 Mhz Ram
eVGA 8800GT SC 512 MB
Samsung SyncMaster 206BW
Asus SATA DVD-RW
Seagate 250 GB SATA II
I am using Leo4all V3 10.5.2 with Vista dual boot (Ntldr, Chain 0, boot.ini, tboot at root of c)
I used shrink option from Vista to create 10 GB space for installation of OSx86.
After that i decided to make one more drive for installation of more Mac softwares (Office, photoshop etc)
So i took out some more space from other Vista drive ..around 15 GB.
I booted to Mac, and using disk utility i formatted that space with Mac OS x journeled.
But after reboot it asked me to "INSERT DISK , BOOT FAILURE".
I repaired with Vista Installation dics in just 2 mins. and booted to Vista. I saw in Disk Manager that This newly created 15 GB partition is set to (Active, Primary partition) , The old 10 GB where my OSx86 is installed is (Primary partition).
I just rebooted my system, and now i can go into OS x. OS x shows all partition properly, including the new 15 GB.
But in Vista it is showing the main OS X installation drive as (Primary), the second OS X 15 GB drive is shown as (Active , Primary) and Vista is (Active, Primary, ......sum more txt )
I have no problem in booting, i can boot selecting OS, but this secondary OS X Partition is shown as Active in Vista. So i am concerned. Is is appropriate ?
Also Inside OS , patching of Marvins utility not taking place. I put patcher , cpuid.txt files in ROOT folder, then run command as
mount -uw /
./patcher ./cpuid.txt
But now they are not getting patched. Saying 0 files patched.
Please help, can any1 tell me if is it because of that Active second OS x partition ??
How to go about Marvin's AMD utility..please help
System config:
AMD Athlon FX60
Asus A8N SLI Deluxe 1805 bios
2 GB Mushkin DDR500 @ 400 Mhz Ram
eVGA 8800GT SC 512 MB
Samsung SyncMaster 206BW
Asus SATA DVD-RW
Seagate 250 GB SATA II