Snow Leopard 10.6.1-10.6.2 Intel AMD made by Hazard - Page 6

snakeo2 · #51 02-11-2010, 03:14 AM

I went out and bought a new drive in order to try installing snow leopard. Everything went fine, except when I reboot and I get the exact message as someone posted below

" "mis-match between kernel and cpu pm". This distro needs the null cpu management kext' ? anyone has any suggestion as to fix this? I will try to install ideneb 10.5.8 and see if that works.However I dont want to have 10 distros, I would like to simply install snow leopard, so I'm open to suggestions.

mr.s4ndm4n · #52 02-11-2010, 04:44 AM

I'm just curious, would it be to long of a list to post if someone were to post a list of most of the best hardware to use for this distro?? I'm pretty new to this, but i'm also pretty desperate to get this distro running on my amd-based PC. So desperate in fact, that i would buy some new hardware to get this working.

I don't know, im just curious about this....

snakeo2 · #53 02-11-2010, 05:49 AM

Look at my specs which I listed somewhere on this thread. I was able to install snow leopard client server 10.6.2 by hazard, but now im having problems registering the damn thing. After searching, I found that some people suggest booting in 32bit mode in order to register, but I'm not quite sure how to boot in 32 bit as everytime I restart, it automatically boots and I dont see the option to press f8 as I did when i was booting off the dvd. Any suggestions?

snakeo2 · #54 02-11-2010, 06:06 AM

can anyone provide a valid serial number for snow leopard server 10.6.2? the one i tried using is not working:

XSVR-106-000-R-LN2-VLQ-PRW-H6C-44L-XH2-P

stereomac23 · #55 02-11-2010, 07:07 AM

to boot into 32 bit mode try holding down 3 and 2 while booting.

snakeo2 · #56 02-11-2010, 03:03 PM

I tried your suggestion but it didnt work. I simply pressed the 3 & 2 together and powered on the computer but didnt work. If it doesnt work, I think I'll do the install again, excpet this time I wont install the server

cottage1909 · #57 02-11-2010, 04:49 PM

Quote:

Originally Posted by snakeo2

I tried your suggestion but it didnt work. I simply pressed the 3 & 2 together and powered on the computer but didnt work. If it doesnt work, I think I'll do the install again, excpet this time I wont install the server

If you dont select the server option in the hazard customisation you wont be asked for a serial number, i wasnt. Not needed for a client install.

If you find a resolution to the mismatch please post it. i am stuck in the same place.

snakeo2 · #58 02-11-2010, 05:14 PM

Thanks for the suggestion, I was aware of that, but wanted to install the server distro. If I cant find a fix, I may just reinstall the client only. So are you able to get to the registration screen? Prior to installation, these are the options I selected, which I found on leohazard website:

Snow_Leopard_Server_10.6.2
AnV_10.2.0_Kernel
Chamelon_RC3_PCEFI_10.5
AMD_Patch
NVEnabler
VoodooHDA_v2.5.3
ATIATA
Realtek_8169
ElliotForceLegacyRTC
IOATAFamily_Fix
OpenHaltRestart

this thread was helpful. Good luck.
http://www.leohazard.com/Forum/viewt...&t=155&start=0

snakeo2 · #59 02-12-2010, 04:43 AM

For those following, I did a reinstall this time without selecting snow leopard server and everything seemed to have gone ok. My network is working, "about this mac" is working and recognizes my amd cuad core and my 4gb ram, etc. I just tried to restart and it froze, so not sure what I did wrong. I will keep testing to see the how stable the OS is on my hardware and report back. Good luck

machinecity · #60 02-12-2010, 09:34 AM

KP at first boot. SL10.6.1-10.6.2_SSE2_SSE3_IntelAMDbyHazard, legacy kernel
i have PeintiumD and Asus P5LD2 Deluxe
and ideas?

thanks
machinecity