|
Use Transmission, quiting often have an error.
|
That shouldn't happen. Are you sure you burned the Disc at its lowest speed at 2x (what burning software did you use?) I suggest you use SwiftDisc 2.02 Premium Burning by: Primo Software, 30-day trial to burn your disks. I'm seeing you have a GA_K8NSNXP-939 (Nforce 3 chipset, how do I know, I used to own the 754-socket version of that board, and used to encounter problems quite often, =). I have a Nforce4 K8NXP-SLI board currently. My best option is to burn at lowest speed "or" study the problem more carefully because you may have to tweak your BIOS setting here any there. Do you see any errors when you are in Verbose Mode? Don't press F8 to get to the installation screen, just press enter when your BIOS is at the point when it is booting of the DVD. =)
Quote:
|
OOps zephyroth....the new image did the same trick by endless reboot loop while installing from DVD once again...Could you please tell me why?Or the hardware did NOT support? Tho,really appreciate you kind and hard work!!!
Regards & Thanx!! Kael |
Finally got my first working install with this version, but it only works if I install without any of the drivers. So default video only and no network for me. I'm new at this so I guess I'll be spending days searching forums and Google trying to figure out how to get my video card and network working but hey, at least I'm up and running! Thanks Zeph!
Soltek K8TPro-939 w/ onboard VIA VT6122 Gigabit LAN AMD 64 4200 Geforce 7600 GS 512mb |
Damn!!
i am stuck in the 1 minute left again,and when i reboot still waiting for root. ps. @ zephyroth on your next ppf can you put the asrock uli chipset 0x522910B9 on the sata section of the appleviaata kext,because if you put it at the ata section you can enable ide1 and ide2 and udma but not sata controler.thanks!!! |
For me it worked only in single boot (only tryed darwin on mbr) and with the nforce 2,3,4,.. third party driver (without the latter "still waiting for root device"). Even if the installation hanged on last minute, it was installed.
Gigabyte k8n sli amd 3800 x2 ati x550 (using callisto) |
I was able to install rev2 on my computer but just like the rev1, there is no sound and no lan.
forcedeth detects the card, assigns the IP but it says no cable plugged, network down. As for the audio, it's not even detected. ASUS M2N-E w/ nForce 570 Chipset AMD X2 4800+ 2GB DDR2 eVGA 8800GT Installed on 80GB IDE. Any ideas how to fix sound and lan issue on M2N-E board with nForce 570 chipset? It would be appreciated. Thanks |
I just tryied install the new 10.5.2 Rev.2 and i am constantly getting the multi-language "You must restart your computer"
Boot on dvd and after some minutes trying to load shows up this screen. 10.5.2 Rev.1 works like a charm, i have installed many versions before and never had problems like that. :( AMD Athlon 64 3000+ Asus A8V-E SE Saphire ATI Radeon X1300 Pro Onborad network is off on Bios Realtek RTL8139/810x Family Fast Ethernet NIC VIA Rhine III Fast Ethernet Adapter 1GB RAM DDR HD SATA 200 (Leopard/Backup) and HD SATA 250 (Windows XP/VIsta/Backup) |
Is there any solution for the "Chain booting error" ... ???
Thanks |
I fixed the EXC_BAD_ACCESS (SIGBUS) issue -- my RAM was set too fast @ CL2.0, just went back and set it as "auto" and it didn't have any problems then. Installation successful!
However, I got a blank screen when I booted into Leopard (when the video and welcome screen supposed to come up, after the grey loading screen). I tried doing -v -x but that didn't catch any errors since the problem comes up after that....any ideas? AthlonX2 3800+ on Abit AN8 mobo 2x512 DDR400 ram on dual channel Geforce 7950GX2 SATA DVD Drive IDE Hard Drive |