InfiniteMac OSx86
Page 11 of 25 « First < 910 11 121321 > Last »
Show 50 post(s) from this thread on one page

InfiniteMac OSx86 (http://infinitemac.com/forum.php)
-   Leopard 10.5 (http://infinitemac.com/forumdisplay.php?f=85)
-   -   Beginners: Ask here first (http://infinitemac.com/showthread.php?t=201)

A_DoNuT333 03-01-2008 12:06 PM
Quote:
[cite] A_DoNuT333:[/cite]thanks but I always use -v when I install-makes me feel like it is actually doing something other than spinning an icon ;).
No this happens after that all loads. I think it is trying to load the main intall GUI but it just stops when the cursor loads in the upper left corner. I can move the cursor but nothing happens.
Hey, I still have this problem. I tried to remove forcedeth.kext using -s on dvd bootup but that got me no where. I'm not even sure it removed it at all. This is very frustrating because I am so close to seeing the installer it's not even funny. Any help is appreciated...again. Thanks.

Snapshot of screen: http://i32.photobucket.com/albums/d22/benyboy08/blankscreenLeo.jpg

Christian 03-01-2008 12:25 PM
Can someone help me fix this error? Heres my computers specs: http://exposedwire.net/specs.html

and heres the error i get:

Partition Failed

Partition Failed with the error:

Input/output error

I get that error when i try to re-partition the harddrive

dreampowder 03-01-2008 03:58 PM
hello, i have been trying to install 10.5.2 zephyroth on my HP COMPAQ NX6125 Laptop. (AMD Turion64 ML-34 CPU, Atix200GPU). the installation starts with no problem, but when i start the installation, the progres bar moves a little bit and then it stops. while this is happening i can still use my mouse and click on the menus at top.. but the laptop is starting to overheating, and after a few minutes it shuts down due to overheating. is there anything you know abot this issue?

A_DoNuT333 03-01-2008 09:22 PM
@dreampowder
The install shouldn't make your computer over heat by itself. You need to make sure you laptop is properly ventilated and if that still does not help, go by a cooling pad for it.
Back to your issue, is there any harddrive activity or DVD activity while it's not moving?

dreampowder 03-01-2008 10:21 PM
@A_Donut333

i am using a cooling pad already.. dvd seems to be working for a while but then it also stops. and theres not much harddisk activity either..

ziska 03-03-2008 12:44 AM
Hi all,

this is my configuration :
ASROCK AM2NF3 VSTA
Athlon 64X2 4200+

My problem is :
I can"t boot the new AMD EFI 10.5.2 Zephyroth on my system ..; because it always freezes on the blank OSX page (which ask you to reboot) and with the -x (and also the -s) command it freezes on the blank page (but without asking you to reboot)..

What's the problem with my configuration ?
Do i have to change something on my system ?

thanks a lot and congratulations to zephyroth !

crawle 03-03-2008 02:56 AM
Start with -v flag and make a photo of your kernel panic.

-crawle

ziska 03-03-2008 09:17 PM
1. http://img240.imageshack.us/img240/6954/image001vz4.jpg
2. http://img529.imageshack.us/img529/4058/image002wz0.jpg
3. http://img529.imageshack.us/img529/4849/image003xs1.jpg

Ps : sorry if the picture is too small XD i couldn't do better ....
you'll need to make a huge zoom to decrypt it

it's writing : "writing OSOwned"

thank you very but very very much !

Puttabong 03-03-2008 09:21 PM
ziska, sorry, but we really can't see anything on that pictures!

Anders 03-03-2008 10:23 PM
I installed 10.5.2 rev. 1 and I have a couple of issues:

When installing I need to have an IDE drive plugged in, not really an issue but still...
After installation I can't boot (same with GUID & MBR, tried both). Need rd=disk0s1 when booting from the DVD
Network is SLOW (rtl8139 pci). I have a nforce network card too, but it doesn't seem to load it or so
Can't load NVinject, says something about an undefined symbol in IOKit.kext (looks like a mangled C++ symbol)
Even though I picked 9.2.0 kernel, it installed the 9.0.0 kernel... ideas?

That's about it for now, otherwise seems quite nice :) Thanks!