Anyone with a P5K Deluxe (or similar board with the same Marvell network PHY), I have made my own plist kext for the Yukon2. It works for me in both 64 and 32 bit modes. I can't take credit for it, I used info from several posts from different users, credit goes to them.

Hi what did you change in the dsdt so it only works with 8gb of ram? Did you fix hpet/rtc for quadcores, because fassls dsdt patcher is not quit right?

I'm I still the only one with working headphone at frontpanel?

Very nice, but keep in mind that the LegacyYukon2.kexy "old plist only injector" also stopped working at 10.5.7 but for the time being this might be prefect.

I'll try this one thank you...

BTW do you guys also have "wifi as en0" and "ethernet as en1"?

sorry, but if I create 2 partition on my hd, one to extract the dmg image and the other to install the new system... then what shall I do to remove the partitions that are not needed and further standardize the partition of the new operating system to the full capacity of the disk?

thanks

and sorry for my English... :D

From my understanding when you decompile the DSDT, the amount of RAM you have installed is intertwined with the DSDT. So after mods and recompile, the amount of RAM you had installed is incorporated into the DSDT. Yes, I applied the quadcores, hpet and rtc fixes. Along with the power button sleep function (which doesn't work for me). And, the audio fix I mentioned in the previous post.

It is working for me. Strange you mentioned that it stopped working at 10.5.7. Still works for me in 10.5.8. Also, I do not have my wifi kext installed in 10.6. I only have en0 and en1 (realtek lan and marvell lan).

BTW, what are you using for audio? I am of the lazy category and not hooked up the connectors to my motherboard. Sometime soon I will tho (it's only been like 2 years since I got this board, you'd think I would have done it by now).:eek:

Hi what is exactly different with the quadcore fix? HPET/RTC seems to look the same to me...

BTW do also have speedstep applied to dsdt? I also heard it was possible also for quads and even corei7...

Sleep fix
 

Hi

Sleep work for me with this method :
http://www.insanelymac.com/forum/ind...owtopic=168014

i apply this method for SATA and it work, no more need for AHCIportinjector.kext

audio also work fine with dsdt patch and AD1988b.Fix.kext front panel (headphone and micro) work, the only problem is low microphone level and i have microphone only in front panel (someone know how to fix the volume level ? ? )

Now i got all working fine and stable in 64 bit with chameleon 2 rc1

note : when i boot for the first time after instal i need to boot with "archi386" 32bit , and launch the Kext utility after that boot normal, and all work

boot direct with the default 86_64 cause kernel panic

(sorry for my english :p)


My motherboard : ASUS P5E + 8800 gts 512

here is my dsdt file with fix for : (Graphic) - (Audio) - (Sata) and (Sleep fix)

I did that also and couldn't see any changes ( I thought I did something wrong but now seeing your DSDT the USB0 TO USB6 section it's the same , so I guess that was not enough for me ...

What method exactly ? Can you please explain, or show the section of DSDT that patches SATA ?

audio also work fine with dsdt patch and AD1988b.Fix.kext front panel (headphone and micro) work, the only problem is low microphone level and i have microphone only in front panel (someone know how to fix the volume level ? ? )

From what I remember microphone was always low level on AD1988B , but with the latest fix it got much better (at least front panel mic works good for me, rear mic works but very low volume ) I just had to turn the mic volume at max in system preferences and now I ca have a decent Skype or Yahoo call without shouting.

btw> What do you set in Bios AC97 or HDAudio in the onboard components
section

And since your sleep is working can you tell us also power management settings of your BIOS? (S1, S2, S3, Auto, resume video , Apic 2.0) ?