|
Thanks a lot wwbsox!
Edit: So far so good =D I can wake on kb/mouse now, I'm ecstatic. Now.. onto my sleep on idle issue. heh. |
What issue are you having with sleep on idle?
|
Well I'm afraid this did not fix my usb keyboard not being detected @ startup, every other restart. =(
If I disable usb kb support in BIOS it won't work in Chameleon selection screen right? haha so no point in trying that =/ My issue with sleep on idle was this: I had the DVD burner causing sleep on idle to fail, as detailed here:http://www.insanelymac.com/forum/ind...&#entry1238915 (The last point is mine, which gives more detail) Before it was a usb drive that was causing it, but I did a fresh reinstall, and I have yet to plug in any DVD drive to the system (install from HDD to HDD), and it fails to go to sleep when it is scheduled to. I believe I hear the drive make a noise at that time, so I think the system does try, but something isn't letting it. and another issue: The screensaver doesn't come up =P No matter what I set the different time intervals to, screensaver, power off display, sleep computer, etc. I use this to work around the init issue my graphics card has. To go into specifics: This only happens when the display is powered off, and I'm still @ the computer, so I immediately move the mouse to bring the screen back on. Again, this only happens when I do it quickly, the monitor doesn't even finish going into standy, before I move the mouse. It is only in this condition, that once the screen comes back on, I get this crazy, pure static like image. It eventually initializes properly and I see my desktop again after a few seconds. Sometimes several. This card has always done that with me. Whether I enabled it through EFI strings or DSDT. If anyone has any input on what I can do to fix this, that'd be very much appreciated, but for now I use the screensaver as a middle-step, so then that becomes the moment where I move the mouse to get the desktop back haha =P. Then if I really am AFK, then it can turn off display, sleep, whatever. |
Quote:
|
And that sticked? dang, odd solution but hey if it works. I'm not going to reinstall though hehe.
btw, I just noticed I have my 8800GT listed in sys prof as PCI card. Everything works and I have input kDawgs code exactly as listed but without checking the proper PCI bus so at PCI0. This is still ok right? Thx http://a.imagehost.org/0301/PCI.png |
Can you re-run set up without installing I'm sure theres a way
|
http://kttns.org/ztux
Bus: PCIe Is the only diff I see... Anyone recommend a fix for my usb-kb not being detected every now and then on startup? I'm on a GA-P35-DS3L, Cham2. GFX, Ether, this USB-fix, Legacy HDA, through DSDT. Edit: I just noticed that I had to re-plug in my Printer to print something =/. What is causing this? My mouse has never been affected... Should I try this strings in Cham's boot.plist? <key>EHCIacquire</key> <string>Yes</string> <key>UHCIreset</key> <string>Yes</string> <key>USBBusFix</key> <string>Yes</string> I'm not exactly sure if they'd conflict with this combined fix in this thread. Anyone? |
@EnzoFX
I have messaged a few others with your mother board and they are not experiencing the same issues. If you'd like, post your dsdt and I will take a look at it. See if I can figure it out. |
DSDT Speed Step
@Everyone with Gigabyte boards
Anybody have working p-states/c-states using dsdt? I am thinking of starting a dsdt speed step thread for gigabyte boards..... unless anyone knows of a good one already. I have not modified my dsdt for speed step...yet. But CPU-I shows it is working somewhat. The multiplier and frequency are throttling up and down, but the voltage remains at the highest p-state (kinda defeats the purpose). |
CPU-I?
How to check speedstep? |