InfiniteMac OSx86
Page 1 of 2 1 2 >
Show 50 post(s) from this thread on one page

InfiniteMac OSx86 (http://infinitemac.com/forum.php)
-   Leopard 10.5 (http://infinitemac.com/forumdisplay.php?f=85)
-   -   Boot only in safe mode... (http://infinitemac.com/showthread.php?t=464)

gipo 02-23-2008 03:18 AM
Hello... first of all thanks to Zephyrot for his great work...
Then...
I can boot only in safe mode...
Now i'm writing in safe mode... all seems to work, except for audio, even LAN that was a pain on tiger.
But i can boot only with -x flag.
If i boot normal... and -v "still waiting for root device" or in graphic mode i can see a stop signal over the apple...


Cpu: DualCore AMD Athlon 64 X2, 2860 MHz (13 x 220) 5200+ (Windsor)
MB: Asus M2N32-SLI Deluxe (bios v.1402)
Ram: 2Gb DDR2-800 DDR2 SDRAM
<----------------------------------------------------------------------------------------------------------------------------------->
GPU: nVIDIA GeForce 7600 GS --> working
Audio onboard: Analog Devices AD1988B --> not work
1° Lan onboard: Gigabit LAN Controller (PHY: Marvell 88E1116) PCI --> work and seem stable (with 680i LAN fix by MikeInNs) --> Topic on insanelymac
2° Lan onboard: Gigabit LAN Controller (PHY: Marvell 88E1116) PCI --> same as above
WLan: Realtek RTL8187L: --> not tried yet
Parallel ATA: mcp51 --> working (last medevil)
Serial ATA: mcp55 --> working (OTB)
Extra SATA: Sil3132 --> working (OTB)
USB 2.0 --> working
Internet Access trought ---> ADSL Router Ethernet

Ianxxx 02-23-2008 05:02 AM
Did you install drivers for your graphics card?

gipo 02-23-2008 05:39 AM
Yes.. installed inject 512 and nvidia drivers 10.5.2 (the first voice)

Ianxxx 02-23-2008 06:40 AM
Did you check that your device ID is included in nvinject, geforce.kext nvdaresman.kext nvdanv40hal.kext?

gipo 02-23-2008 06:52 AM
Do you think it's a graphic board issue? but it's working perfectly in safe mode... 1680*1050 and in system info there is:

Graphics by NVIDIA:

Modello Chipset: Graphics by NVIDIA
Tipo: Monitor
Bus: PCIe
Larghezza Lane PCIe: x16
VRAM (totale): 512 MB
Fornitore: NVIDIA (0x10de)
ID dispositivo: 0x0392
ID revisione: 0x00a1
Revisione ROM: NVinject 0.2.0
Monitor:
SyncMaster:
Risoluzione: 1680 x 1050 @ 60 Hz
Profondità: Colore 32-bit
Core Image: Software
Monitor principale: Sì
Mirror: Spento
Online: Sì
Quartz Extreme: Non Supportata
Mostra connettore:
Stato: Nessun monitor collegato

Ianxxx 02-23-2008 05:32 PM
Its not working perfectly you don't have quartz extreme.
I would check those kexts I bet you dont have your device ID in all of them

gipo 02-23-2008 09:28 PM
Can i use the same kext i used in Tiger? i think were titan drivers...

zephyroth 02-23-2008 09:30 PM
Yes you can gipo

gipo 02-23-2008 09:41 PM
i'll do it this evening when i'll be home from work... anyway Zeph... this a great work!!! Thanks again...
Another problem (i'll try to resolve in a second time...) is the death screen that appear sometimes, maybe the lan drivers.
Another question for moderators... is it not possible to put a signature in profile? just to write in all the specs about hardware of our pc...

gipo 02-24-2008 05:17 PM
Nothing to do... i rebooted a hundred times, changing kexts, installing the old tiger kexts, installings punk's92 new drivers... nothing.
In installation must i check nvinject 256 and 10.5.2 pack or only one of them?
Anyway my id is 10DE 0392 (from gpu-z)... where must i add this info and i which files?
Is it surely a graphic driver's problem? i installed the mbr bootloader because i think (there is a way to understand if it is mbr or guid in this moment?) it was so in tiger... i formatted partition and installed Leo, i don't want to partition hd 'cause i've got a lot of stuff on it.