|
#1
|
|||
|
|||
How Can I burn The MAC OS X distro to USB flash memory?
I want to use USB flash driver as a retail DVD.
to try different Distros with different kext by using my Flash memory as DVD. I think I can boot computer with USB flash memory and I want to burn the osx Distro to USB. How can I achieve this? |
#2
|
|||
|
|||
With "Disk Utility" from OS X.
|
#3
|
||||
|
||||
just make sure you enable a bootloader such as chameleon or EFI to make the partition on your flash drive.
|
#4
|
|||
|
|||
nfoav8or, thanks for reply.
how can I sure or do bootlader to make the partition on your flash drive. I DONT mean that I want to run OSX on flash memory. I mean that I want to run DVD such as kalyway on flash memory. instead of DVD , I will plug Flash memory and I will start installation. can you say how can I do this with Which Steps? Thanks |
#5
|
||||
|
||||
Boot up normally into OS X and then run Disk Utility. Either insert the DVD or find the .iso you used to write the DVD (the .iso is faster) and select the flash drive on the left. Then select Restore on the top tab and place the respective items in the Source and Destination fields. This will take a while so sit back and read a book or browse the web. When its done, close Disk Utility and open the Chameleon installer ... and select your USB drive as the installation destination and it should work.
Last edited by nfoav8or; 11-08-2008 at 07:22 PM. Reason: Link removed and replaced with "..." |
#6
|
|||
|
|||
thank you very much , I am using mac os x , i will try now.
|
#7
|
|||
|
|||
Quote:
-transfer the image i want to use unto the MAc hdd -plug in my external hdd (formated to HFS+) -Select restore and select my iso as the source and my externall as the destination -open the chameleon installer (how and where do i do this? b/c im new to macs) and select my external usb as he installation destination (is this step to install the actual running OSX on my external ? b/c I dont want to do that. and hopefully i can skip this step) CPU: AMD Phenom 9600 Chipset: 790G SB700 (looking for the kext for it now) Audio:Realtek ALC888 Lan: Realtek 8111C Video:ATI Radeon HD 3200 unimportant stuff: Ram: 4 x 1GB 240 pin ddr2 @ 1066mhz Hdd: 40 gb (IDE) (FAT32) 250 gb (SATA) (NTSF) External 1TB (HFS+) External 250 GB (NTSF) Audio interfaces: Mobile Pre, FW Solo, Lexicon Alpha, Motu, etc. This whole rig is for production purposes www.myspace.com/natewil |
#8
|
|||
|
|||
No success
Im glad some of you have made it that far! As for me, I am unable to boot from the flash drive, it gives me EBIOS read error, as if its reading from a bad disk. I have used the recovery from a ISO and installed chameleon onto it, all with no succes! anyone have any ideas? Im using a sandisk cruzer 4gb on a striker ii extreme mobo
|
#9
|
|||
|
|||
Quote:
Leopard 10.6.5 | Core i3 | Gigabyte H55M-USB3 | ATI 5770 | Coolermaster Cosmos |
#10
|
|||
|
|||
Which image format do you have to use when converting ISO to DMG (compressed, sparse, ...)?
I've tried using the iPC ISO directly and never got anything bootable, the PC would attempt to boot from the stick, but all I got was a blinking cursor. My previous attempts went like this... - I had created 1 journaled partition on my 8GB stick with MBR - Restored from ISO with Erase Destination unchecked - if checked it complained about the image (source needs to be imagescanned/scanned) - Installed EFI loader with OSX86Tools Last edited by ArKayDe; 03-22-2009 at 12:24 PM. |