UHCI/EHCI Built in with dsdt fix - Page 6

EnzoFX · #1 09-03-2009, 01:10 AM

Thanks a lot wwbsox!

Edit:
So far so good =D
I can wake on kb/mouse now, I'm ecstatic. Now.. onto my sleep on idle issue. heh.

wwbsox · #2 09-03-2009, 01:57 AM

What issue are you having with sleep on idle?

EnzoFX · #3 09-03-2009, 03:59 AM

Well I'm afraid this did not fix my usb keyboard not being detected @ startup, every other restart. =(
If I disable usb kb support in BIOS it won't work in Chameleon selection screen right? haha so no point in trying that =/

My issue with sleep on idle was this:
I had the DVD burner causing sleep on idle to fail, as detailed here:http://www.insanelymac.com/forum/ind...&#entry1238915 (The last point is mine, which gives more detail)
Before it was a usb drive that was causing it, but I did a fresh reinstall, and I have yet to plug in any DVD drive to the system (install from HDD to HDD), and it fails to go to sleep when it is scheduled to. I believe I hear the drive make a noise at that time, so I think the system does try, but something isn't letting it.

and another issue: The screensaver doesn't come up =P No matter what I set the different time intervals to, screensaver, power off display, sleep computer, etc. I use this to work around the init issue my graphics card has. To go into specifics: This only happens when the display is powered off, and I'm still @ the computer, so I immediately move the mouse to bring the screen back on. Again, this only happens when I do it quickly, the monitor doesn't even finish going into standy, before I move the mouse. It is only in this condition, that once the screen comes back on, I get this crazy, pure static like image. It eventually initializes properly and I see my desktop again after a few seconds. Sometimes several. This card has always done that with me. Whether I enabled it through EFI strings or DSDT. If anyone has any input on what I can do to fix this, that'd be very much appreciated, but for now I use the screensaver as a middle-step, so then that becomes the moment where I move the mouse to get the desktop back haha =P. Then if I really am AFK, then it can turn off display, sleep, whatever.

Snow · #4 09-03-2009, 11:13 AM

And that sticked? dang, odd solution but hey if it works. I'm not going to reinstall though hehe.

btw, I just noticed I have my 8800GT listed in sys prof as PCI card. Everything works and I have input kDawgs code exactly as listed but without checking the proper PCI bus so at PCI0.

This is still ok right?

Thx

EnzoFX · #5 09-03-2009, 09:08 PM

Bus: PCIe Is the only diff I see...

Anyone recommend a fix for my usb-kb not being detected every now and then on startup?
I'm on a GA-P35-DS3L, Cham2. GFX, Ether, this USB-fix, Legacy HDA, through DSDT.

Edit: I just noticed that I had to re-plug in my Printer to print something =/. What is causing this? My mouse has never been affected...

Should I try this strings in Cham's boot.plist?
<key>EHCIacquire</key>
<string>Yes</string>
<key>UHCIreset</key>
<string>Yes</string>
<key>USBBusFix</key>
<string>Yes</string>

I'm not exactly sure if they'd conflict with this combined fix in this thread. Anyone?

wwbsox · #6 09-04-2009, 11:01 AM

@EnzoFX

I have messaged a few others with your mother board and they are not experiencing the same issues. If you'd like, post your dsdt and I will take a look at it. See if I can figure it out.

wwbsox · #7 09-04-2009, 11:05 AM

@Everyone with Gigabyte boards

Anybody have working p-states/c-states using dsdt?

I am thinking of starting a dsdt speed step thread for gigabyte boards..... unless anyone knows of a good one already.

I have not modified my dsdt for speed step...yet. But CPU-I shows it is working somewhat. The multiplier and frequency are throttling up and down, but the voltage remains at the highest p-state (kinda defeats the purpose).

Ianxxx · #8 09-14-2009, 04:19 PM

Quote:

Originally Posted by EnzoFX

Anyone recommend a fix for my usb-kb not being detected every now and then on startup?
I'm on a GA-P35-DS3L, Cham2. GFX, Ether, this USB-fix, Legacy HDA, through DSDT.

Enzo if your still having this prob, I know it might sound stupid but make sure that your keyboard is plugged in to one of the usb sockets nearest the board, I sometimes have this glitch with my microsoft habu mouse but doesn't happen if I plug it in to one of those two ports "same board as you ga-p35-ds3l rev 2"

Snow · #9 09-05-2009, 07:57 AM

Quote:

Originally Posted by Snow

And that sticked? dang, odd solution but hey if it works. I'm not going to reinstall though hehe.

btw, I just noticed I have my 8800GT listed in sys prof as PCI card. Everything works and I have input kDawgs code exactly as listed but without checking the proper PCI bus so at PCI0.

This is still ok right?

Thx

I haven't changed anything except remove the dsdt.aml from my root dir and keep it in E/E and the GFX is now listed as PCI-e

I'm not complaining though, just an odd observation, has a mind on its own apparently.

wwbsox · #10 09-05-2009, 01:56 PM

@Snow

My apple keyboard shows up in system profiler under high speed usb bus, my rocketfish apple mouse shows up just under usb. Also, I found a page that has the DSDT entry for your Q6600 to enable speedstep with all the p-states enabled. Gotta find the link again, I will get that to you later. I just need to find it for my Q9550.

Here is CPU-i.