[AMD] Snow Leopard 10A432 Install

[DEADLY360]

hey perisman
i now know why nth pops out after i reboot, since i got two HDD so i forgot to set the snow hdd to 1st boot in bios. Now it boots perfectly but just my mouse and keyborad dosen't work(i added ApplePS2 and controller ) but it didn't work. I havn't test sound and lan i'll check it
now i need help on mouse and keyboard.

[mr_kite]

Mine has a phenom 2.5 and is running iatkos 10.6.3 very nicely using an nvidia 9500 gt card. I installed with just via chipset (supervia i believe it is) and nvenabler and I use NO NETWORK DRIVER at all and it detects my SMC gigabit card. the internal one is realtek 1000 or 8169 driver I believe but try no driver first because that may work. If i put in a realtek driver (either one) it detects card b ut doesn't connect to internet at all. in reg leopard 10.5.8 i used realtek 1000 driver, but discovered the no driver trick for Snow Leopard and have used it on other machines with realtek cards/chips. I can't seem to get 64bit to work though and I'm not sure why... (anyone have this MB working at 64 bit out there?) but with Quartz Extreme and 4 gigs ram, it's pretty damn fast! I also have a pentium Duo Quad machine running same drivers except it's intel chipset (same graphics same sound chip) and it runs 64 bit no problem. Best way to see if a MB will be 64 bit is just install chipset and nvenabler drivers first and see if it comes up in 64 bit. then add drivers one at a time for sound and network and check to see if still booting 64 bit.

Good luck!

[mr_kite]

Mine has a phenom 2.5 and is running iatkos 10.6.3 very nicely using an nvidia 9500 gt card. I installed with just via chipset (supervia i believe it is) and nvenabler and I use NO NETWORK DRIVER at all and it detects my SMC gigabit card . the internal onboard chip is realtek 1000 or 8169 driver I believe but try no driver first because that may work. (I have gigabit router so I disabled onboard chip) If i put in a realtek driver (either one) it detects card but doesn't connect to internet at all. in reg leopard 10.5.8 i used realtek 1000 driver, but discovered the no driver trick with Snow Leopard and have used it on other machines with realtek cards/chips. I can't seem to get 64bit to work though and I'm not sure why... (anyone have this MB working at 64 bit out there?) I also have a pentium duo core 4 machine running same drivers except it's intel chipset (same graphics same sound chip) and it runs 64 bit no problem. Best way to see if a MB will be 64 bit is just install chipset and nvenabler drivers first and see if it comes up in 64 bit. then add drivers one at a time for sound and network and check to see if still booting 64 bit. The AMD is nice though because it supports virtual machines so you can use parallels which I like better than VMWare which is all I can run on my intel machine...

Good luck!

[mbrubaker]

I have followed the instructions at the site "http://www.ihackintosh.com/2009/09/install-snow-leopard-106-on-amd-pc-hackintosh/" to try to install SL on my system with an ECS IC780M-A motherboard with an AMD Athlon II 250 CPU (dual core 3.0 Ghz). It uses the Modbin test7 kernel. When I try to boot the installation I get the following error message after the gray screen with the silver Apple logo:

"panic(CPU 0 caller 0x2e71f459):"Unsupported CPU:family=0x10,model=0x6,stepping=0x2"@/SourceCache/AppleIntelCPUPowerManagement/Apple/IntelCPUPowerManagement-90/pmProcessor.c:210"

Can anyone help?

[perisman]

for ps2 use voodoops2controller for snow 64 bit in /extra/extensions, and for audio voodoohda.kext for snow 64 bits, in S/L/E, and deleting applehda.kext.

[DEADLY360]

Originally Posted by perisman for ps2 use voodoops2controller for snow 64 bit in /extra/extensions, and for audio voodoohda.kext for snow 64 bits, in S/L/E, and deleting applehda.kext.

perisman
My keyboard works well but the mouse dosen't even move ( IMAGE DOWN )
i did use ApplePS2controller.kext too but the result is same, i remade the extensions.mkext too but the result is same

[razza]

Originally Posted by DEADLY360 perisman My keyboard works well but the mouse dosen't even move ( IMAGE DOWN ) i did use ApplePS2controller.kext too but the result is same, i remade the extensions.mkext too but the result is same

Hello DEADLY360,

if are using PS2, you have to place this kext in /Extras/Extensions

AppleACPIPS2Nub.kext
ApplePS2Controller.kext

I added the file

I hope help you..

[punk_zappa]

Installed and now replying using SL. Audio is still something to be desired (garbled) and still working on it.

[Seawane]

thanks guys for the thread. Everything went fine and I now have a working SL. The only problem for now is sleep/restart/shutdown. I have dsdt.aml made with the patcher but it's not helping(although it helped to get rid of the "CMOS checksum error" during post, which kept reseting the BIOS settings).
@perisman - i see you have the same board as me. Did you get sleep/reset/shutdown working?

[roratonga]

hi, i installed snow leopard on 3 different ways now and everytime i get the same result: after restarting my screen is black and my keyboard turn off. so any ideas how to fix this problem? do i need any special kext for my mainboard?

amd x2 4850e
foxconn a7gm-s (amd 780g / sb700)
corsair xms2 2*2gb ddr2 800
foxconn 8800 gt (g92) 512 mb

greetz rora