Leopard用 AppleHDA.kext オーディオドライバを Snow Leopard へ移植する方法（バイナリ Byte-Flip 置換および Plist 構造の移植ガイド）

mormegil…

It shouldnt matter but as long as all the locations that state layout ID are 889 vs your 12 it should still work right ?

my dsdt is coded with layout-id as 79 03 00 00

and a codec-id of 89 08 EC 10

so I followed all your steps, hexedit found all 4 locations with 8508ec10 and replaced with 8908ec10

edited the two plists as show in the post.

still no go. the 1.5.7a24 AppleHDA and my dsdt file I get audio in SL. but the edited AppleHDA from a SL install does not work.

Any ideas? thanks

mormegil-
I have been going down the same paths as airwalk over and over. Here are two messages that I get over and over on boot:

Sound assertion "0 != createAudioEngines ( fPathMap_aDriverInstance )" failed in "/SourceCache/AppleHDA/AppleHDA-174.1.1/AppleHDA/AppleHDADriver.cpp" & Sound assertion "0 == pathMap_aDriverInstance" failed in "/SourceCache/AppleHDA/AppleHDA-174.1.1/AppleHDA/AppleHDADriver.cpp"

mormegil-
airwalk and I have the same setup. check my linux dump below. we are 889, not 889a.

mormegil...

I am 100 % sure this is the correct codecID since the codec dump I have ( taken by using a linux live dvd) Vendor Id: 0x10ec0889 ie...283904137

which is what is coded in the working applehda.

take a look a these dumps I have from when I patched the applehda for 10.5.6 (these dumps are from my board not downloaded from someone else)

Codec: Realtek ALC889
Address: 2
Vendor Id: 0x10ec0889
Subsystem Id: 0x10de0175
Revision Id: 0x100004

Then based on the dump I generated the verbs.

Question could this be caused by config data not matching pathmaps data?

BTW I tested without changing the hex values and no luck.

yeap its the same pathmapid in both places.

I'll double check the dsdt.

Airwalk did the AppleHDA leopard kext you're using ever list all of the audio configs in system profile?

the reason I was asking that airwalk is because I never had leopard on this board so I have been using your leopard kext that you posted on another forum and after comparing my modified SL kext with some of the others I have seen here I realize that I have significantly less child nodes in my modified sections than other people do...

when using the old applehda I think its version 1.5.7… I allways get system profiler to show the ports correctly.

see screenshot of this applehda 1.5.7 running in SL and it looked the same in Leopard also.

mormegil-

I tried another approach, using lagacyapplehda files I port the same config to the lagacy files and put it in /extra/extensions and put the stock applehda in /S/L/E. in doing so I was able to set the system profiler to show all the ports but in system prefs. there are no inputs and outputs to select from.

any thoughts ?

Alright Mormegil, been a while m8, all good with you?

Since the 10.6.2 update messed up my audio I was wondering if you could take a look at my already slightly (but apparently non working) modded AppleHDA kext.

media fire.com/file/mikkmb25bzz/AppleHDA.zip

bud

ps. using AppleHDA v10.6.1 for now

ok everyone with the evga x58 mobo here is the solution to get HDA working in 64 bit mode.

voodoohda.kext haha just kidding…

1st thank you to everyone that helped in getting this done.

2nd remove and voodoohda you have

what is accomplished. 32 and 64 bit audio using stock applehda.kext in /S/L/E

you must have your dsdt.aml patched with the following info

codec-id",
Buffer (0x04)
{
0x89, 0x08, 0xEC, 0x10
},

"layout-id",
/**** Is ResourceTemplate, but EndTag not at buffer end ****/ Buffer (0x04)
{
0x79, 0x03, 0x00, 0x00

Install the stock applehda.kext in /S/L/E ( I used the one from 10.6.2 update) using kext utilities 2.3.2

and install the attached LegacyHDA.kext in /Extra/Extensions using kext utilities 2.3.2 update mkext.

it will give you 4 outs and 2 ins.

testing in 32 and 64 bit mode. the advantage of doing it this way (at least for me) is that I dont have any modified kexts in /S/L/E.

give it a shot and report back.

Good Luck

i will test it out and report back in a few, you're the man airwalk

Confirmed working. Hopefully netkas has an epiphany that he should make evga x58 boards sleep sometime soon. In the meantime lets plug away, did you ever have sleep working in 10.5?

Muchos Gracias Hombre

Installing right away.

Update: working perfectly after rebuilding Aggregate device bro, thx again

OMG! it works

i got ALC262 (VAIO FW139E/H), confirming that this work! BTW i have installed the following kext as well: ALCInject.kext and HDAEnabler.kext.

Thank you very much mormegil!

atleast my sound works, though i have no mic and HDMI output but hey its better than none. ^_^

p6860fx laptop no sound still :(

Could someone I own a gateway p6860fx laptop. I followed this excellent guide in attempts to get my sound working. I hex edited the applehda using B0 76 1D 11 which matches the Subsystem Id from the codec#1 in this below linux audio dump. It also matches the Vendor ID from the codec#2 linux dump below.

I have pasted my linux dump and DSDT audio patch. Could someone please advise me to maybe why my audio still doesn't work. Sound was fine in Leopard and I modified a Vanilla Snow AppleHDA kext per the guide here.

Linux Dump

Codec: LSI ID 1040
Address: 1
Vendor Id: 0x11c11040
Subsystem Id: 0x107b0690
Revision Id: 0x100200
Modem Function Group: 0x1


Codec: IDT 92HD71B8X
Address: 2
Vendor Id: 0x111d76b0
Subsystem Id: 0x107b0692
Revision Id: 0x100101
No Modem Function Group found
Default PCM:
    rates [0x7e0]: 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
Default Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Default Amp-Out caps: ofs=0x7f, nsteps=0x7f, stepsize=0x02, mute=1
GPIO: io=8, o=0, i=0, unsolicited=1, wake=1
  IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[4]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[5]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[6]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[7]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Power-Map: 0x01
Analog Loopback: 0x00
Node 0x0a [Pin Complex] wcaps 0x400183: Stereo Amp-In
  Amp-In caps: N/A
  Amp-In vals:  [0x00 0x00]
  Pincap 0x0000001c: OUT HP Detect
  Pin Default 0x0321101f: [Jack] HP Out at Ext Left
    Conn = 1/8, Color = Black
    DefAssociation = 0x1, Sequence = 0xf
  Pin-ctls: 0x00:
  Unsolicited: tag=01, enabled=1
  Connection: 3
     0x10 0x11* 0x17
Node 0x0b [Pin Complex] wcaps 0x400081: Stereo
  Pincap 0x00001724: IN Detect
    Vref caps: HIZ 50 GRD 80
  Pin Default 0x03a11020: [Jack] Mic at Ext Left
    Conn = 1/8, Color = Black
    DefAssociation = 0x2, Sequence = 0x0
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=02, enabled=1
Node 0x0c [Pin Complex] wcaps 0x400081: Stereo
  Pincap 0x00001724: IN Detect
    Vref caps: HIZ 50 GRD 80
  Pin Default 0x40f000f0: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x00: VREF_HIZ
  Unsolicited: tag=00, enabled=0
Node 0x0d [Pin Complex] wcaps 0x400183: Stereo Amp-In
  Amp-In caps: N/A
  Amp-In vals:  [0x00 0x00]
  Pincap 0x00000014: OUT Detect
  Pin Default 0x90170110: [Fixed] Speaker at Int N/A
    Conn = Analog, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Connection: 3
     0x10* 0x11 0x17
Node 0x0e [Pin Complex] wcaps 0x400081: Stereo
  Pincap 0x00001724: IN Detect
    Vref caps: HIZ 50 GRD 80
  Pin Default 0x40f000f1: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x1
  Pin-ctls: 0x00: VREF_HIZ
  Unsolicited: tag=00, enabled=0
Node 0x0f [Pin Complex] wcaps 0x400183: Stereo Amp-In
  Amp-In caps: N/A
  Amp-In vals:  [0x00 0x00]
  Pincap 0x00000014: OUT Detect
  Pin Default 0x40f000f2: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x2
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Connection: 3
     0x10 0x11 0x17*
Node 0x10 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
  Amp-Out caps: N/A
  Amp-Out vals:  [0x64 0x64]
  Converter: stream=0, channel=0
  Power: setting=D0, actual=D0
  Delay: 13 samples
Node 0x11 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
  Amp-Out caps: N/A
  Amp-Out vals:  [0x7f 0x7f]
  Converter: stream=0, channel=0
  Power: setting=D0, actual=D0
  Delay: 13 samples
Node 0x12 [Audio Input] wcaps 0x1d0541: Stereo
  Converter: stream=0, channel=0
  SDI-Select: 0
  Power: setting=D3, actual=D3
  Delay: 13 samples
  Connection: 1
     0x1c
  Processing caps: benign=0, ncoeff=0
Node 0x13 [Audio Input] wcaps 0x1d0541: Stereo
  Converter: stream=0, channel=0
  SDI-Select: 0
  Power: setting=D3, actual=D3
  Delay: 13 samples
  Connection: 1
     0x1d
  Processing caps: benign=0, ncoeff=0
Node 0x14 [Pin Complex] wcaps 0x400102: Mono Amp-In
  Amp-In caps: N/A
  Amp-In vals:  [0x80]
  Pincap 0x00000010: OUT
  Pin Default 0x40f000f3: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x3
  Pin-ctls: 0x00:
  Connection: 1
     0x16
Node 0x15 [Audio Selector] wcaps 0x300101: Stereo
  Connection: 3
     0x10* 0x11 0x17
Node 0x16 [Audio Mixer] wcaps 0x200100: Mono
  Connection: 1
     0x15
Node 0x17 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
  Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
  Amp-In vals:  [0x97 0x97] [0x97 0x97] [0x97 0x97] [0x97 0x97] [0x97 0x97]
  Connection: 5
     0x10 0x11 0x27 0x1a 0x1b
Node 0x18 [Pin Complex] wcaps 0x40000d: Stereo Amp-Out
  Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00000020: IN
  Pin Default 0x90a6012e: [Fixed] Mic at Int N/A
    Conn = Digital, Color = Unknown
    DefAssociation = 0x2, Sequence = 0xe
    Misc = NO_PRESENCE
  Pin-ctls: 0x20: IN
Node 0x19 [Pin Complex] wcaps 0x40000d: Stereo Amp-Out
  Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00000020: IN
  Pin Default 0x40f000f5: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x5
  Pin-ctls: 0x20: IN
Node 0x1a [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
  Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-Out vals:  [0x00 0x00]
  Connection: 3
     0x0b* 0x0c 0x0e
Node 0x1b [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
  Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
  Amp-Out vals:  [0x00 0x00]
  Connection: 3
     0x0b* 0x0c 0x0e
Node 0x1c [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
  Amp-Out caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1
  Amp-Out vals:  [0x09 0x09]
  Connection: 4
     0x1a* 0x17 0x18 0x19
Node 0x1d [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
  Amp-Out caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1
  Amp-Out vals:  [0x80 0x80]
  Connection: 4
     0x1b* 0x17 0x18 0x19
Node 0x1e [Pin Complex] wcaps 0x400301: Stereo Digital
  Pincap 0x00000010: OUT
  Pin Default 0x044513a0: [Jack] SPDIF Out at Ext Right
    Conn = Optical, Color = Black
    DefAssociation = 0xa, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Connection: 1
     0x24
Node 0x1f [Pin Complex] wcaps 0x400701: Stereo Digital
  Pincap 0x00010010: OUT EAPD
  EAPD 0x0:
  Pin Default 0x40f000f8: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x8
  Pin-ctls: 0x00:
  Power: setting=D0, actual=D0
  Connection: 2
     0x24* 0x25
Node 0x20 [Pin Complex] wcaps 0x400301: Stereo Digital
  Pincap 0x00000010: OUT
  Pin Default 0x90451360: [Fixed] SPDIF Out at Int N/A
    Conn = Optical, Color = Black
    DefAssociation = 0x6, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Connection: 1
     0x25
Node 0x21 [Audio Output] wcaps 0x40211: Stereo Digital
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  PCM:
    rates [0x7e0]: 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Delay: 4 samples
Node 0x22 [Audio Output] wcaps 0x40211: Stereo Digital
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  PCM:
    rates [0x7e0]: 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Delay: 4 samples
Node 0x23 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x24 [Audio Selector] wcaps 0x300101: Stereo
  Connection: 3
     0x21* 0x1c 0x1d
Node 0x25 [Audio Selector] wcaps 0x300101: Stereo
  Connection: 3
     0x22* 0x1c 0x1d
Node 0x26 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
  Amp-Out caps: ofs=0x03, nsteps=0x03, stepsize=0x17, mute=1
  Amp-Out vals:  [0x00]
Node 0x27 [Pin Complex] wcaps 0x400000: Mono
  Pincap 0x00000020: IN
  Pin Default 0x40f000f7: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x7
  Pin-ctls: 0x00:
Node 0x28 [Volume Knob Widget] wcaps 0x600000: Mono
  Volume-Knob: delta=1, steps=127, direct=1, val=127
  Connection: 2
     0x10 0x11

DSDT Patch

Device (HDEF)
            {
                Name (_ADR, 0x001B0000)
                Method (_DSM, 4, NotSerialized)
                {
                    Store (Package (0x06)
                        {
                            "codec-id", 
                            Buffer (0x04)
                            { 
                               0xB0, 0x76, 0x1D, 0x11
                            },                             
                            "layout-id", 
                            Buffer (0x04)
                            {
                                0x0C, 0x00, 0x00, 0x00
                            }, 

                            "PinConfigurations", 
                            Buffer (Zero) {}
                        }, Local0)
                     Return (Local0)
                }
            }

Thanks, mormegil, your AppleHDA kext works well in my system (EP35-DS3r with ALC889a).
I attach a AppleHDA.kext > Contents > Resources > Spanish.lproj folder to include into the kext for anybody who likes to see device names in spanish instead of english.
Thanks again.

I can't get this to work, I've spent hours and hours trying I have a Foxconn Blackops with ALC885. Patched DSDT as such:

            Device (HDEF)
            {
                Name (_ADR, 0x001B0000)
                Method (_PRW, 0, NotSerialized)
                {
                    Return (Package (0x02)
                    {
                        0x0D,
                        0x05
                    })
                }

                Method (_DSM, 4, NotSerialized)
                {
                    Store (Package (0x0A)
                        {

                            "built-in",
                            Buffer (0x01)
                            {
                                0x01
                            },

                            "codec-id",
                            Buffer (0x04)
                            {
                                0x85, 0x08, 0xEC, 0x10
                            },

                            "layout-id",
                            Buffer (0x04)
                            {
                                0x0C, 0x00, 0x00, 0x00
                            },

                            "device-type",
                            Buffer (0x011)
                            {
                                "ALC885"
                            },

                            "PinConfigurations",
                            Buffer (0x28)
                            {
                                /* 0000 */ 0x10, 0x40, 0x01, 0x01, 0x64, 0x10, 0x01, 0x01,
                                /* 0008 */ 0x71, 0x60, 0x01, 0x01, 0x82, 0x20, 0x01, 0x01,
                                /* 0010 */ 0x30, 0x90, 0xA1, 0x01, 0x20, 0x90, 0xA1, 0x02,
                                /* 0018 */ 0x40, 0x30, 0x81, 0x01, 0x50, 0x40, 0x21, 0x02,
                                /* 0020 */ 0xF0, 0x71, 0x44, 0x01, 0x90, 0x71, 0x45, 0x11
                            }
                        }, Local0)
                    DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0))
                    Return (Local0)
                }
            }

Also tried the 889A version of the above (and updated layout id to 889 for that, in DSDT and plists) to no avail.

Layout ID is correct (12) for ALC885 in both DSDT and plists.

On boot I always get:

Nov 19 11:04:04 localhost kernel[0]: Sound assertion "0 != setupHostInterrupt ()" failed in "/SourceCache/AppleHDA/AppleHDA-179.1.4/AppleHDAController/AppleHDAController.cpp" at line 312 goto Exit

I have taken the Layout and PathMap settings from my working Leopard AppleHDA.kext, but clearly something isn't right.

Working Leopard kext plist:

82.113.155.91/leopard-info.plist

Hacked SL plists:

AppleHDAHardwareConfigDriver-info.plist (82.113.155.91/AppleHDAHardwareConfigDriver-info.plist)
AppleHDAPlatformDriver-info.plist (82.113.155.91/AppleHDAPlatformDriver-info.plist)

edit: fixed links!

If anyone can give me a clue as to where I might be going wrong I'd be very grateful, this is driving me nuts I can get sound with VoodooHDA but only through the headphone socket, no lineout

Tried adding HDAEnabler.kext to /Extra/Extensions as a potshot but it still fails.

Nov 19 11:57:34 localhost kernel[0]: HDAEnabler: Copyright (c) 2008 by Kabyl
Nov 19 11:57:34 localhost kernel[0]: HDAEnabler: 05/05/2008 Added SPAudio support:Taruga
Nov 19 11:57:34 localhost kernel[0]: HDAEnabler: Copyright (c) 2008 by Kabyl
Nov 19 11:57:34 localhost kernel[0]: HDAEnabler: 05/05/2008 Added SPAudio support:Taruga
Nov 19 11:57:34 localhost kernel[0]: Sound assertion "0 != setupHostInterrupt ()" failed in "/SourceCache/AppleHDA/AppleHDA-179.1.4/AppleHDAController/AppleHDAController.cpp" at line 312 goto Exit
Nov 19 11:57:34 localhost kernel[0]: Sound assertion ""ERROR: EFI ROM did not publish 'hda-gfx' associative property!\n"" failed in "/SourceCache/AppleHDA/AppleHDA-179.1.4/AppleHDA/AppleHDACodecGeneric.cpp" at line 331 goto ExitError

Still not working Pretty sure DSDT is correct now:

            Device (HDEF)
            {
                Name (_ADR, 0x001B0000)
                Method (_DSM, 4, NotSerialized)
                {
                    Store (Package (0x04)
                        {
                            "layout-id",
                            Buffer (0x04)
                            {
                                0x0C, 0x00, 0x00, 0x00
                            },

                            "PinConfigurations",
                            Buffer (Zero) {}
                        }, Local0)
                    DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0))
                    Return (Local0)
                }
            }

Device shows up in system profiler with the correct device and layout id, but still AppleHDA.kext won't load, still gives the same error.

Any ideas? kext plists are unchanged from my first post

Interestingly enough, if I leave DSDT with AZAL in it rather than HDEF like this:

            Device (AZAL)
            {
                Name (_ADR, 0x001B0000)
                Method (_PRW, 0, NotSerialized)
                {
                    Return (Package (0x02)
                    {
                        0x0D,
                        0x05
                    })
                }
            }

VoodooHDA works, but I only get the headphone socket rather than the line-in. But if I patch DSDT (as in previous post), VoodooHDA kernel panics immediately on load.

I'm lost.. i've spent over 3 days messing around with this, i'm almost ready to give up and buy an Xmod

leo-HDAController-info.plist (82.113.155.91/leo-HDAController-info.plist)

I did actually try putting this block into HDAController/Info.plist in the snow leopard AppleHDA.kext last night:

      <key>HDAConfigDefault</key>
      <array>
        <dict>
          <key>CodecID</key>
          <integer>283904133</integer>
          <key>ConfigData</key>
          <data>
          AUccEAFHHUABRx4RAUcfAQFXHBIBVx0gAVce
          AQFXHwEBZxwRAWcdYAFnHgEBZx8BAXccFAF3
          HRABdx4BAXcfAQGHHDABhx2ZAYceoQGHHwEB
          lxw/AZcdkAGXHqEBlx8CAaccMQGnHTEBpx6B
          AacfAQG3HB8Btx1AAbceIQG3HwIBxxwyAccd
          AQHHHjMBxx+ZAdccAAHXHQEB1x4AAdcfQAHn
          HGAB5x0BAeceRQHnH4EB9xwAAfcdAQH3HgAB
          9x9A
          </data>
          <key>FuncGroup</key>
          <integer>1</integer>
          <key>LayoutID</key>
          <integer>12</integer>
        </dict>
      </array>

But still didn't work

mymayin,

Try this, download the LegacyHDA file Airwalk posted here How to port AppleHDA to SL →
modify it using your working Leo data, you know HDAController, Layouts and Pathmaps. Put the LegacyHDA in your Extra folder and trash your extensions.mkext and rebuild it with mkextTool, replace your modify AppleHDA with a vanilla file from SL. It should work and it's a better solution because it maintains AppleHDA untouched no need to modify it every time you update your OS. Don't forget to remove any other audio file i.e. VoodooHDA and any other enabler. Build your DSDT the way he did it don't put the pin configuration, keep it simple for now "codec-id" and "layout-id". Good Luck

Still not working

I think my DSDT might be wrong somehow, I don't see any devices in Profiler->Audio, just the device id and layout id (both are correct).

it says Devices: but the listing is blank.

Vanilla AppleHDA.kext is failing to load.

            Device (HDEF)
            {
                Name (_ADR, 0x001B0000)
                Method (_DSM, 4, NotSerialized)
                {
                    Store (Package (0x04)
                        {
                            "layout-id",
                            Buffer (0x04)
                            {
                                0x0C, 0x00, 0x00, 0x00
                            },

                            "PinConfigurations",
                            Buffer (Zero) {}
                        }, Local0)
                    DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0))
                    Return (Local0)
                }
            }

I tried adding the codec-id in there and increasing Store(Package) size to 0x08 but that didn't help either

So you put the legacyHDA.kext in Extra and rebuild the extensions.mkext reboot and still nothing, that's odd.
Did you add this to your DSDT? DTGP code, read The King's guide, you probably did because the compiler would complain if you didn't.
http://www.projectosx.com/forum/index.php?showtopic=465… ↗

Are you using Chameleon? what version is it?

Yeah I did all that, I'm using Chameleon 2.0RC1. I'll see if there's a later version..

still no luck with pc-efi 10.5, same errors on boot

Nov 20 21:16:46 localhost kernel[0]: Sound assertion "0 != setupHostInterrupt ()" failed in "/SourceCache/AppleHDA/AppleHDA-179.1.4/AppleHDAController/AppleHDAController.cpp" at line 312 goto Exit

I noticed I don't have anything pointing to AZAL or HDEF in the _GPE section of the DSDT. Could this be the problem?

eg: http://www.insanelymac.com/forum/index.php?showtopic=18… ↗

there the guy has:

        Method (_L05, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.HDEF, 0x02)
        }

whereas my _GPE section looks like:

    Scope (_GPE)
    {
        Method (_L00, 0, NotSerialized)
        {
            Notify (\_TZ.THRM, 0x80)
        }

        Method (_L03, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.USB0, 0x02)
        }

        Method (_L04, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.USB1, 0x02)
        }

        Method (_L0C, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.USB2, 0x02)
        }

        Method (_L0E, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.USB3, 0x02)
        }

        Method (_L05, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.USB4, 0x02)
        }

        Method (_L20, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.USB5, 0x02)
        }

        Method (_L0D, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.EHC1, 0x02)
            Notify (\_SB.PCI0.EHC2, 0x02)
            Notify (\_SB.PCI0.IGBE, 0x02)
        }

        Method (_L0B, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.HUB0, 0x02)
        }

        Method (_L08, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.PX40.UAR1, 0x02)
            Notify (\_SB.PCI0.PX40.UAR2, 0x02)
        }

        Method (_L09, 0, NotSerialized)
        {
            If (LNotEqual (VID0, 0xFFFF))
            {
                If (LEqual (And (RSR0, One), One))
                {
                    Store (0xFF, RSR0)
                    Store (0x80, PMC0)
                    Notify (\_SB.PCI0.PEX0, 0x02)
                }
            }

            If (LNotEqual (VID1, 0xFFFF))
            {
                If (LEqual (And (RSR1, One), One))
                {
                    Store (0xFF, RSR1)
                    Store (0x80, PMC1)
                    Notify (\_SB.PCI0.PEX1, 0x02)
                }
            }

            If (LNotEqual (VID2, 0xFFFF))
            {
                If (LEqual (And (RSR2, One), One))
                {
                    Store (0xFF, RSR2)
                    Store (0x80, PMC2)
                    Notify (\_SB.PCI0.PEX2, 0x02)
                }
            }

            If (LNotEqual (VID3, 0xFFFF))
            {
                If (LEqual (And (RSR3, One), One))
                {
                    Store (0xFF, RSR3)
                    Store (0x80, PMC3)
                    Notify (\_SB.PCI0.PEX3, 0x02)
                }
            }

            If (LNotEqual (VID4, 0xFFFF))
            {
                If (LEqual (And (RSR4, One), One))
                {
                    Store (0xFF, RSR4)
                    Store (0x80, PMC4)
                    Notify (\_SB.PCI0.PEX4, 0x02)
                }
            }

            If (LNotEqual (VID5, 0xFFFF))
            {
                If (LEqual (And (RSR5, One), One))
                {
                    Store (0xFF, RSR5)
                    Store (0x80, PMC5)
                    Notify (\_SB.PCI0.PEX5, 0x02)
                }
            }
        }
    }

maybe i should add that in? perhaps using a different unused _L0x?

There should be 2 instances of AZAL replaced to HDEF. I thing you are close

I figured out the missing part, I added HDEF to the _L0D method:

        Method (_L0D, 0, NotSerialized)
        {
            Notify (\_SB.PCI0.EHC1, 0x02)
            Notify (\_SB.PCI0.EHC2, 0x02)
            Notify (\_SB.PCI0.IGBE, 0x02)
            Notify (\_SB.PCI0.HDEF, 0x02)
        }

But still no sound with AppleHDA

This is too much of a headache, i give up, im buying an Xmod

Hey!, thanks for this sweet guide, it really helped me port the applehda kext to work for my alc888!

Ok I'm following TheKing's guide, but I'm stuck on how to convert the output from VerbIt to the encoded format used in the ConfigData parameter in Info.plist:

Verbs from Linux Codec Dump File: codec_dump.txt

Codec: Realtek ALC885   Address: 2   DevID: 283904133 (0x10ec0885)

   Jack   Color  Description                  Node     PinDefault             Original Verbs
--------------------------------------------------------------------------------------------------------
    1/8   Green  Line Out at Ext Rear        20 0x14   0x01014410   21471c10 21471d44 21471e01 21471f01
    1/8   Black  Line Out at Ext Rear        21 0x15   0x01011412   21571c12 21571d14 21571e01 21571f01
    1/8  Orange  Line Out at Ext Rear        22 0x16   0x01016411   21671c11 21671d64 21671e01 21671f01
    1/8    Grey  Line Out at Ext Rear        23 0x17   0x01012414   21771c14 21771d24 21771e01 21771f01
    1/8    Pink  Mic at Ext Rear             24 0x18   0x01a19c40   21871c40 21871d9c 21871ea1 21871f01
    1/8    Pink  Mic at Ext Front            25 0x19   0x02a19c50   21971c50 21971d9c 21971ea1 21971f02
    1/8    Blue  Line In at Ext Rear         26 0x1a   0x0181344f   21a71c4f 21a71d34 21a71e81 21a71f01
    1/8   Green  HP Out at Ext Front         27 0x1b   0x02214c20   21b71c20 21b71d4c 21b71e21 21b71f02
  ATAPI Unknown  CD at Int ATAPI             28 0x1c   0x593301f0   21c71cf0 21c71d01 21c71e33 21c71f59
  ATAPI Unknown  Line In at Int ATAPI        29 0x1d   0x598301f0   21d71cf0 21d71d01 21d71e83 21d71f59
   Comb   Black  SPDIF Out at Ext Rear       30 0x1e   0x014b1130   21e71c30 21e71d11 21e71e4b 21e71f01
    1/8   Black  Speaker at Ext Rear         31 0x1f   0x411111f0   21f71cf0 21f71d11 21f71e11 21f71f41
--------------------------------------------------------------------------------------------------------


   Jack   Color  Description                  Node     PinDefault             Modified Verbs
--------------------------------------------------------------------------------------------------------
    1/8   Green  Line Out at Ext Rear        20 0x14   0x01014410   21471c10 21471d40 21471e01 21471f01
    1/8   Black  Line Out at Ext Rear        21 0x15   0x01011412   21571c60 21571d10 21571e01 21571f01
    1/8  Orange  Line Out at Ext Rear        22 0x16   0x01016411   21671c70 21671d60 21671e01 21671f01
    1/8    Grey  Line Out at Ext Rear        23 0x17   0x01012414   21771c80 21771d20 21771e01 21771f01
    1/8    Pink  Mic at Ext Rear             24 0x18   0x01a19c40   21871c40 21871d90 21871ea1 21871f01
    1/8    Pink  Mic at Ext Front            25 0x19   0x02a19c50   21971c50 21971d90 21971ea1 21971f01
    1/8    Blue  Line In at Ext Rear         26 0x1a   0x0181344f   21a71c90 21a71d30 21a71e81 21a71f01
    1/8   Green  HP Out at Ext Front         27 0x1b   0x02214c20   21b71c20 21b71d40 21b71e21 21b71f01
  ATAPI Unknown  Line In at Int ATAPI        29 0x1d   0x598301f0   21d71cf0 21d71d00 21d71e83 21d71f50
   Comb   Black  SPDIF Out at Ext Rear       30 0x1e   0x014b1130   21e71c30 21e71d10 21e71e4b 21e71f01
--------------------------------------------------------------------------------------------------------

How do I convert those hex strings for the ConfigData, which is in this format:

AUccEAFHHUABRx4RAUcfAQFXHBIBVx0gAVce
AQFXHwEBZxwRAWcdYAFnHgEBZx8BAXccFAF3
HRABdx4BAXcfAQGHHDABhx2ZAYceoQGHHwEB
lxw/AZcdkAGXHqEBlx8CAaccMQGnHTEBpx6B
AacfAQG3HB8Btx1AAbceIQG3HwIBxxwyAccd
AQHHHjMBxx+ZAdccAAHXHQEB1x4AAdcfQAHn
HGAB5x0BAeceRQHnH4EB9xwAAfcdAQH3HgAB
9x9A

Alc 262 for snow leopard..please

tks for a lot help!
I need ask a very great favor: send me by mail or download link, the compiled kexts that i need replace in Snow Leopard...christian.max (at) pop.com.br

ALC262 SONY VAIO VGN-NS150AE

Im a inexperient user to compiled my on, so sorry my bad english...

Best regards...i hope some mail about that!

TKS!

Please My firends...post kext....ALC 262

Please...i need that kext modified...AppleHDA.kext for my ALC262...
I suplies for help...just post or send by mail...im very tired to look around (google)

Me Get Realtek ALC889 (Non-A Version) Working in 10.6.2 via DSDT

Hello! I just came across this wonderful thread, and I have tried to patch my DSDT with the code mentioned for the Realtek ALC889 chip, as that is what my motherboard, the Gigabyte GA-X58A-UD7, uses for onboard audio (its little brother, the GA-EX58-UD5, uses the ALC889A).

Since it uses the same model chip as the EVGA motherboards, I believe that I can get it working on this new flagship motherboard from Gigabyte, and thus open the Hackintosh world up to people who are considering buying this motherboard. to help the Hackintosh community. I will come out with a guide for this motherboard as soon as I figure out how to get audio working via DSDT, which will make my current installation a complete vanilla installation.

Just to offer you some background information, I am using the Chameleon v2.0 RC4 bootloader and have already patched my DSDT with ACPI Patcher Beta 5 (under Windows of course). I modified the DSDT that was created by ACPI Patcher with the lines of code for the ALC889 as well as replacing both instances of AZAL found with HDEF, but upon compilation with iASLMe, it gave me one error on the Codec_ID line regarding the length of the statement and 17 optimizations. As such, I removed that line completely and it compiled with zero errors, but still performed 17 optimizations.

correct my DSDT code by providing your entire code or just the excerpts necessary to make corresponding modifications to mine. Also, I still need to get my SATA and ethernet controllers working via DSDT (which both use the same chipsets as the EVGA motherboards), so I can remove my JMicron.kext, AppleIntelPIIXATA per.kext, and RealtekR1000.kext (or RealtekR1000SL.kext), and go fully vanilla.

Currently, I have the LegacyHDA.kext posted in this thread and and the vanilla AppleHDA.kext in S/L/E, and under "Audio (Built In)" in System Profiler, I have two devices showing up in the right column as "Intel High Definition Audio":

1. Device ID: 0x1458A102
Audio ID: 12
Available Devices:

2. Device ID: 0x1682AA30
Audio ID: 12
Available Devices:

Before patching my DSDT, I had nothing showing up under "Audio (Built In)" in System Profiler, so this is definitely a sign of progress. Now, I need the help of you wise InfiniteMac users to get this down perfect, as audio still does not get detected or work for me.

I would like to for your assistance and cooperation, and hope to hear from you as soon as possible.

I have the following sound card and on Leopard I had a fully working AppleHDA so I want to port that kext to Snow Leopard.

HDA Codec #0: IDT 92HD71B7
 HDA Codec ID: 0x111d76b2
       Vendor: 0x111d
       Device: 0x76b2
     Revision: 0x03
     Stepping: 0x02
PCI Subvendor: 0x361b103c

I followed the guide and added b2761d11 to the AppleHDA file with Hex editor.
My old kext was using Layout 1 so I didn't change it and kept everything as it was in my old kext.

Finally, I edited the HDA Enabler kext according to the one that I used on Leopard, which uses Layout 1 and also a Config data.

On my system profiler, it is listed as below,

Intel High Definition Audio:

  Device ID:    0x103C361B
  Audio ID:    1
  Available Devices:
  Headphone:
  Connection:    1/8-Inch Jack
  External Microphone:
  Connection:    1/8-Inch Jack
  Speaker:
  Connection:    Internal
  External Microphone:
  Connection:    1/8-Inch Jack
  Internal Microphone:
  Connection:    Internal
  S/P-DIF Out:
  Connection:    RCA

This is also what appeared on Leopard's System Profiler. So everything seems ok but unfourtanely there is no sound. I attached the file I created if anyone is interested in looking at.

I tried to use DSDT for my sound card but I couldn't do it.

Thanks for your help.

A problem with IDT HDA

Audio according to Windows:
Vendor: 111D
DevID: 76D8

0x293e8086

Snow Leopard 10.6.0
Everything is working but audio is not. However, it works with VoodooHDA although I neither can control volume nor I have mic.

I've read here that it's possible to get it working with working AppleHDA from Leopard. Unfortunately, I don't have any. Probably it's possible to use PinConfig from Windows? I've seen one in the registry.

I just setup a new hackintosh box using SL 10.6.0 10A432 on a Gigabyte Motherboard GA-945GCM-S2L.

Gigabyte's site says that it uses the ALC662 Codec but my SL install shows me

Device ID: 0x1458A002
Audio ID: 66

and that's how I found this thread. I do not have any files from Leopard, any chance of helping me get some audio going please.

In 32-bit mode ...

you can use Appleazaliaaudio.kext for Output, a small usb-soundcard (Terratec AureonUSB) for Micro if needed. This will prevent the cracking noise during startup (if USB is used for Output) and the sound assertion errors in verbose mode.

Attached is my HDEF-Section from DSDT (GA945GCM-S2L)

Hello, I have this problem: I have a Sony Vaio laptop VGN-AR41M and a Realtek ALC262 audio device onboard. I have Iatkos 10.5.7 installed and using AppleHDA patcher and ALC262 dump codec text I have no problem to get sound. I'd like to use Snow Leopard and I tried to follow this guide to use my working AppleHDA Leopard kext in SL, but I have no success. I've injected my DSDT file and I thinks it's ok. In System Profiler, under audio section, I have the sound card output recognized. But under preferences sound I have no output at all.
Could you help me, please? Is there anyone with Realtel ALC262 working under SL with patched AppleHDA?

@mormegil

Please, mormegil, could you take a look at the attachments?
I can't get it work it out!

P.S. please rename the attached pdf to rar to open it

I'm here again with my problem with ALC262... please, momegil, help me...
I have this error message in the boot sequence:

ALCinject: Starting.
Apr 28 21:48:01 Mac-di-Marco kernel[0]: ALCinject: Setting built-in=<data not shown>
Apr 28 21:48:01 Mac-di-Marco kernel[0]: ALCinject: Setting layout-id=<data not shown>
Apr 28 21:48:02 Mac-di-Marco kernel[0]: Sound assertion "0 == fAudioFunctionGroup" failed in "/SourceCache/AppleHDA/AppleHDA-174.1.1/AppleHDA/AppleHDACodecGeneric.cpp" at line 202 goto ExitError
Apr 28 21:48:02: --- last message repeated 1 time ---
Apr 28 21:48:02 Mac-di-Marco kernel[0]: Sound assertion "0 == pathMap_aDriverInstance" failed in "/SourceCache/AppleHDA/AppleHDA-174.1.1/AppleHDA/AppleHDADriver.cpp" at line 1459 goto Exit
Apr 28 21:48:02 Mac-di-Marco kernel[0]: Sound assertion "0 != createAudioEngines ( fPathMap_aDriverInstance )" failed in "/SourceCache/AppleHDA/AppleHDA-174.1.1/AppleHDA/AppleHDADriver.cpp" at line 172 goto Exit
Apr 28 21:48:02 Mac-di-Marco kernel[0]: Sound assertion "0 == pathMap_aDriverInstance" failed in "/SourceCache/AppleHDA/AppleHDA-174.1.1/AppleHDA/AppleHDADriver.cpp" at line 1459 goto Exit
Apr 28 21:48:02 Mac-di-Marco kernel[0]: Sound assertion "0 != createAudioEngines ( fPathMap_aDriverInstance )" failed in "/SourceCache/AppleHDA/AppleHDA-174.1.1/AppleHDA/AppleHDADriver.cpp" at line 172 goto Exit

Do you know what would it be the problem?

I tried another AppleHDA version and I get a different error:

22:42:59 localhost kernel[0]: kxld[com.apple.driver.AppleHDA]: The super class vtable __ZTV13IOAudioEngine for vtable __ZTV14AppleHDAEngine is out of date. Make sure your kext has been built against the correct headers.
Apr 29 22:42:59 localhost kernel[0]: Can't load kext com.apple.driver.AppleHDA - link failed.
Apr 29 22:42:59 localhost kernel[0]: Failed to load executable for kext com.apple.driver.AppleHDA.
Apr 29 22:42:59 localhost kernel[0]: Kext com.apple.driver.AppleHDA failed to load (0xdc008016).
Apr 29 22:42:59 localhost kernel[0]: Failed to load kext com.apple.driver.AppleHDA (error 0xdc008016)

Any little help?

Hey... Glad to hear that there is a possibility for my lost sound in snow leopard

I have a fully working applehda in leopard 10.5.8.
after installation of sl (10.6.2) my sound is gone, so i followed the instructions and did everything like in this thread but it doesn't work. I use hdaenabler + applehda in my leopard and it works very nice. i downloaded a hdaenabler for sl and installed it with my patched applehda for sl - no luck

can anybody help me please?
Here is my working applehda from 10.5.8

m1330, stac9228 and this guide here

im one of the people, which lost their sound in SL with the stac9228. i tried voodoohda in sl and all sound outputs/inputs worked except the internal speakers.

then i found this guide and i tried it. so now THANKS.. my internal speakers work now.. but - now my internal and my external mic doesnt work.

my problem is.. i just followed this guide on page 1.. but do really not understand what ive done with this hex numbers and plist editing and so on...

maybe someone can help me!

p.s. i hope u can understand me, because iam german..

now this is an easy guide, however, I do not have a working applehda.kext, I'm basically starting from scratch. No other guide seems to have a clear method of doing this, I've read Kings guide but that's incomplete and all over the place.

hi mormegil...

just want to say thanks! cos this is one of the best tutorials out there...

however,,,i'm in the same boat as hassan..i have no leopard applehda to work from...

i do have a working voodoohda and all the info (verbs etc),,,and have tried my best to work from there.

dsdt fix made system profiler display
Intel High Definition Audio:
Audio ID: 12

editing legacyhda and applehda with the info you gave makes system profiler list all the proper devices..
line-out 1/8 jack
line-in 1/8 jack etc etc

BUT, nothing shows in audio/midi setup...and no sound (:(

do i reinstall leopard and start from scratch, or can we make this work from voodoo info and codec dumps?

thanks again!

**EDIT**
i've installed leopard on a spare drive for testing.
the aim is to get a working leopard applehda to work from.

the best i can do is DSDT patch (which enables sys prof output)
and a patched apple hda (which populates system prof output)

problem is,

system prof shows
mic built in
mic external
speakersheadphones
SPDIF OUT!

but in the audio midi setup i only have

mic built in
mic external
speakers/headphones

how can this be? i've tried adding pin configs (from the same source that got my voodoohda working)

voodoo hda the same problem where it would autodetect everything except SPDIF.

Spdif was made to work by adding my own config data.

would anyone out there be prepared to help me make an applehda.kext for SL from scratch.

i have working pin configs, which are put in the dsdt, so system profiler shows my devices perfectly.

no matter what i do though, i can't get sound with applehda…

pm me if you're interested in helping.

i've given up on encoded output via voodoohda,,since no on at all seems to have it.

Sorry for bringing up an old thread, but this seems like the best place to ask...

I have a working applehda and want to convert it to 10.6.5 applehda. I found that in 10.6.5 I do not have a MacOS folder and no actual AppleHDA inside.

I was wondering if someone could help me put together a 10.6.5 HDA as I've been stuck trying this tutorial.

Thank you so much,

Haze